View S5A1903X01-E0R0_1303987.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA PROCESSOR
S5A1903X01
INTRODUCTION
32-LQFP The S5A1903X01 implements the voice intelligibility processor (VIP). The VIP is a signal processing algorithm designed to increase the intelligibility of human speech in a high ambient noise environment. Unlike noise cancellation or adaptive speech filtering systems, VIP operates on the speech signal only and is totally independent of the noise. This approach makes speech clearer and easier to understand regardless of the characteristics of the noise source, and eliminates the need for processing of the noise signal. In addition to VIP, the S5A1903X01 includes voice equalizer. The equalizer is composed of four different frequency bands, and each band is controlled between +12dB and -12dB. Thus, it can be used to compensate of speaker characteristics. The Figure 1 shows how the S5A1903X01 interfaces to Vocoder and Codec in cellular phone.
MAIN FEATURES
* * * * * * IP Mode Equalizer Mode 16-bit Fixed Point DSP Core Two Internal 256-word Data RAM 2K-word Internal Program ROM Wide Range of System Clock : 8 - 40 MHz -- PCM Input/ Output Interface -- I2C Host Interface -- Low Power Consumption less than 4mA in working mode 10uA in sleep mode -- Packages: 32-LQFP/ 32-BCC -- 3V Single Power Supply
ORDERING INFORMATION
Device S5A1903X01-E0R0 Package 32 LQFP Temperature Range 0C - 70C
APPLICATIONS
* * Cellular Phone Wireless and Traditional Telephone
1
S5A1903X01
DATA PROCESSOR
BLOCK DIAGRAM
System Block Diagram
CKIN
RESB SCL SDA VOCODER DIN FS MCLK
VIP
DOUT
VOICE CODEC
2
DATA PROCESSOR
S5A1903X01
Chip Block Diagram
SRAM 256 MSM VOCODER I 2C I/F
SRAM 256
SSP1611
Digital I/F CODEC P.ROM 2K
VIP NOTE: Not Scaled
3
S5A1903X01
DATA PROCESSOR
Functional Block Diagram
Voice Intelligibility Proces
DIN
PCM INPUT I/F
BPF (Center: 300HZ) BPF (Center: 600HZ)
DOUT
PCM OUTPUT I/F
+ BPF (Center: 1.2kHZ) HPF (Cutoff: 2.4kHZ)
4
DATA PROCESSOR
S5A1903X01
PIN ASSIGNMENTS
TSHFTDR
TSEKDR0
TSELDR1
TUPDDR
TCLKDR
GND3
VDD3 18 8 RESB
TIDR
25 VDD4 26 TODR 27 GPO3 28 GPO2 29 DOUT 30 GND4 31 GPO1 32 1 GPO0
24
23
22
21
20
19
17 16 SCL 15 SDA 14 GND2
S5A1903X01 32BCC (Top View)
13 CKIN 12 VDD2 11 MCLK 10 DIN
2 VDD1
3 GPI0
4 GPI1
5 GPI2
6 GPI3
7 GND1
FS
SAS 9
5
S5A1903X01
DATA PROCESSOR
PIN DESCRIPTION
Related Block PIN NAME RESB HIU SDA SCL SAS DIN CIU DOUT FS MCLK System CKIN GPI0 GPI1 GPI2 GPI3 TSELDR0 TSELDR1 TEST TUPDDR TSHFTDR TIDR TCLKDR TODR GPO0 GPO1 GPO2 GPO3 Power Ground VDD1, VDD2 VDD3, VDD4 GND1, GND2 GND3, GND4 PIN NO. 8 15 16 17 10 30 9 11 13 3 4 5 6 19 20 21 23 24 25 27 1 32 29 28 2, 12, 18, 26 7, 14, 22, 31 I/O I I/O I I I O I I I I I I I I I I I I I O O O O O P G I2C Serial Data I2C Serial Clock I2C Address Selection 16 Bit PCM Serial Data In 16 Bit PCM Serial Data Out PCM Data Frame Sync. PCM Data Bit Clock System Clock (9.84MHz) Test Pin0 (Host INT. Indicator) Test Pin1(0:No Fade, 1:Fade) Test Pin2 (0:RAM Test) Test Pin3 (0:Codec Bypass) Test Pin for JTAG Test Pin for JTAG Test Pin for JTAG Test Pin for JTAG Test Pin for JTAG Test Pin for JTAG Test Pin for JTAG Host Ack. Pin Host Test Output Host Test Output Host Test Output Digital Power (+3.0V) Digital GND Description Reset: Active Low
6
DATA PROCESSOR
S5A1903X01
DSP PORT ASSIGNMENT FOR I/F WITH PERIPHERALS
I/F HIU Read/ Write Read Write CIU Read Write Port EXT1 EXT1 EXT0 EXT0 INT0 Interrupt INT1
HARDWARE SPECIFICATION
CODEC INTERFACE UNIT (CIU) --- Time Diagram
FS
MCLK
DIN
1
2
3
4
5
6
7
~ ~
15
16
DOUT
1
2
3
4
5
6
7
~ ~
15
16
Important!: During FS (Frame Sync. Clock) high, the falling edge of MCLK (PCM Bit Clock) should exist one time.
~ ~
7
S5A1903X01
DATA PROCESSOR
HOST INTERFACE UNIT (HIU) -- 2C Bus Interface I The VIP can be controlled by a microcontroller via the 2-line I2C bus, SDA (Serial Data Line) and SCL (Serial Clock Line). Both lines must be connected to a positive supply via pull-up resistor. Data transfer may be initiated only when the bus is not busy. When the bus is free, both lines are high. The data on the SDA line must be stable during the high period of clock, SCL. When the SCL is low, the SDA can change. Every byte transferred through the SDA line must contain 8 bits including programmable slave address and read/write direction control bit. Each byte must be followed by acknowledge bit which is sent back to the microcontroller by the VIP by pulling down the SDA line. The MSB is transferred first. -- 2C bus interface start and stop condition I The start condition is high to low transition of the SDA line while the SCL is high. The stop condition is low to high transition of the SDA line while SCL is high.
SDA
SCL Data Valid
Change of data Allowed
SDA
SCL
S Start Condition
P Stop Condition
8
DATA PROCESSOR
S5A1903X01
-- 2C Bus Interface Acknowledge I The acknowledge related clock pulse is generated by a microcontroller. The transmitter releases the SDA line (high) during the acknowledge clock pulse. The receiver must pull down the SDA line during the acknowledge clock pulse so that it remains stable low during the high period of this clock pulse. The slave-transmitter generates negative acknowledge when read operation processes. The negative acknowledge is generated by a master (microcontroller).
I2C Bus Interface Format-Write Operation Chip Address MSB LSB Function Address MSB LSB A MSB DATA LSB AP
S 1 0 0 0 0 0 A0 W A
SCL
SDA S
1 0000 0 0 0
P
I2C Bus Interface Format-Read Operation Chip Address MSB LSB Function Address MSB LSB A MSB DATA LSB
N/ A
S 1 0 0 0 0 0 A0 R A
P
SCL
SDA S
1 0000 0 0 1
P
9
S5A1903X01
DATA PROCESSOR
COMMAND
SUMMARY IC Address 80H 80H 80H 80H 80H 80H 80H 80H 80H Command 01H 02H 03H 04H 05H 06H 07H 08H 09H Bit[7:5] 000B 80H 0AH 001B 010B 011B 80H 0BH Bit [7:4] 0H 80H 0CH **H Bit [3:0] 0H - CH VIP Filter1 Gain Control Bit [3:0] = 0H: +12dB, Bit [3:0] = CH: 0dB, 1dB Step VIP Filter10 Gain Control Noise Level Selection Return Current Status followed by IC Read Address 0x81, [7:4] = Unused, [3:2] = VIP Level, [1] = Working Mode(0:VIP, 1:EQ), [0] = Bypass Flag (0: DSP ON, 1: DSP OFF) Return Band1 Tone Level Status followed by IC Read Address 0x81 (00H: -12dB - 18H: + 12dB) Return Band2 Tone Level Status followed by IC Read Address 0x81 Return Band3 Tone Level Status followed by IC Read Address 0x81 Return Band4 Tone Level Status followed by IC Read Address 0x81 00000H 11000H Data 00H 01H 02H Bit[4:0] Band1 Gain Control Band2 Gain Control Band3 Gain Control Band4 Gain Control Host Test Mode (Return **H). Read after IC Read Address 0x81 VIP Equalizer Equalizer Flat Equalizer Mode1 Equalizer Mode2 Equalizer Mode3 Equalizer Mode4 VIP Level 100% VIP Level 80% VIP Level 60% Description Bypass (Default, DSP OFF)
... 9H
0H - CH 0H - CH 00H - FFH
80H
0DH
80H
01H
80H 80H 80H 80H 0EH
01H 02H 03H 04H
10
DATA PROCESSOR
S5A1903X01
DESCRIPTION -- Bypass Mode * Format Command Code (Hex) 01 * Description In bypass mode, DIN (PCM input data line) is directly connected to DOUT (PCM output data line) and the DSP is in stop mode. -- VIP MODE * Format Command Code (Hex) 02 * Description Command Name VIP Command Name Bypass
This one byte command selects VIP mode. EQUALIZER MODE * Format Command Code (Hex) 03 * Description This one byte command selects Equalizer mode. Default tone levels are dipicted in Command Name EQ
11
S5A1903X01
DATA PROCESSOR
10
0
-10
-20
-30 102 103
Figure 1: Default Tone Level (Band1: + 4dB, Band2: 0dB, Band3: 0dB, Band4: +1dB) -- VIP Level Select * Format Command Code (Hex) Data (Hex) 00 04 01 02 * Description VIP Level Command Name Description 100% (Max.) 80% (Mid.) 60% (Min.)
When the current mode is the VIP, its level can be changed using incoming data byte after the command. The default VIP level is 80%.
12
DATA PROCESSOR
S5A1903X01
-- EQ Mode Select * Format Command Code (Hex) 05 06 07 08 09 * Description Command Name EQ Flat EQ Mode1 EQ Mode2 EQ Mode3 EQ Mode4 Description All Bands are set to 0dB Band1: +3dB, Band2: -1dB, Band3: -1dB, Band4: +1dB Band1: +3dB, Band2: 0dB, Band3: 0dB, Band4: +3dB Band1: +5dB, Band2: 0dB, Band3: 0dB, Band4: 0dB Band1: +5dB, Band2: 0dB, Band3: 0dB, Band4: +1dB
Although equalizer can control all four bands, it assigns five preset tone level modes. -- EQ Tone Select * Format Command Code (Hex) Data [7:5] 00 01 10 11 [4:0] 0A 00000 00001 | 01100 | 10111 11000 * Description -11dB -12dB 0dB Description Band1 Select Band2 Select Band3 Select Band4 Select +12dB +11dB Tone Control Command Name
The equalizer controls four different frequency bands. The gain for each frequency band can be controlled between -12dB and +12dB. The [7:5] in data byte after the command determines the frequency band to be controlled and [4:0] determines gain level.
13
S5A1903X01
DATA PROCESSOR
-- VIP Filter Gain Selection * Format Command Code (Hex) Data (Hex) 0 1 2 3 [7:4] 0B 4 5 6 7 8 9 0 [3:0] 1 C * Description Description 150Hz Filter Gain to Servo 300Hz Filter Gain to Servo 150Hz & 300 Hz Sum Gain 600Hz Filter Gain to Servo 1.2kHz Filter Gain to Summer 1.2kHz Filter Gain to Servo 2.4kHz Filter Gain to Summer 2.4kHz Filter Gain to Servo 4.8kHz Filter Gain to Summer 4.8kHz Filter Gain to Servo + 12dB + 11dB ..... 0dB VIP Filter Gain Control Command Name
These commands select the gains of filter outputs in the VIP mode. The detailed description of filter structure can be found in "VIP specification" published by SRS Labs.
14
DATA PROCESSOR
S5A1903X01
-- Noise Level Selection * Format Command Code (Hex) 0D * Description Data (Hex) 00 - FF Description Assume the value in data as noise level Command Name Noise Level Select
When the input from ADC has small noise, this noise can incresed in VIP or EQ mode since the specific frequency levels are increased. To avoid this problem in mute, the input data is tested for 25ms. If the absolute values of input data are less than noise level specified in Data and stay for 25ms, then the input is considered as zeros and are processed. Default noise level is set to 0x1F. -- Current Status * Format Command Code (Hex) 0E * Description Data (Hex) 01 Description Return current status register contents Command Name Current Status
It returns the contents of the current status register as: Status [7:4] = unused Status [3:2] = VIP Level (00: 100%, 01: 80%, 10: 60%) Status [1] = Working Mode (0: VIP, 1:EQ) Status [0] = DSP On/Off (0: DSP On, 1: DSP Off) -- EQ Tone Level Status * Format Command Code (Hex) Data (Hex) 02 0E 03 04 05 Description Return current band1 tone level Return current band2 tone level Return current band3 tone level Return current band4 tone level Current Tone Level Status Command Name
*
Description
These commands return the current tone levels in EQ mode. Returned byte value is between 0x00 (-12dB) and 0x18 (+12dB).
15
S5A1903X01
DATA PROCESSOR
MEMORY SIZE AND REQUIRED MIPS
MEMORY SIZE Memory Data Bank 0 Bank 1 VIP 4band EQ Program Test Others Total * word = 16 bit MIPS Routines VIP 4band EQ Others No. of Cycles 650 400 80 MIPS 5.2 3.2 0.64 Remark Working only when VIP is OFF Size (word*) 256 256 800 500 400 100 1860
Total (VIP ON) = 650 + 70 + 80 = 800 (6.4 MIPS)
16
DATA PROCESSOR
S5A1903X01
8. ELECTRICAL CHARACTERISTICS
(Unless otherwise specified, Vcc = 2.7V to 3.3V, TA = -30xC to 85xC ; typical characteristic are specified at Vcc = 3.0V, TA = 25xC; all signals are referenced to GND) DIGITAL INTERFACES Symbol VIL VIH Parameter Input Low Voltage Input High Voltage IOL = 1uA VOL Output Low Voltage IOL = 4mA (see Note1) IOL = 8mA (see Note 2) IOH = -1uA VOH Output High Voltage IOH = -4mA (see Note1) IOH = -8mA (see Note2) IIL Input Low Current VIN = Vss VIN = VSS (see Note3) IIH Input High Current VIN = VDD VIN = VDD (see Note4) IOZ Output Current in High impedance (Tri-state) VOUT = VSS or VDD -10 -60 -10 60 -5 30 -30 10 -10 10 10 5 uA uA uA uA uA VDD-0.05 2.4 V V Test Condition Min. 0.8 1.9 0.05 0.4 Typ. Max. Unit V V V V
NOTES: 1. Normal Output Pin 2. SDA ,SCL Output Pin 3. Input Buffer with pull -up (RESB Pin) 4. Input Buffer with pull -down (2, 3, 4, 5, 6, 17, 19, 20, 21, 23, 24, 25 Pin)
POWER DISSIPATION (@3.3V) Symbol ICC0 ICC1 ICC2 Parameter Operation Current Bypass Current Static Current Test Condition VIP or EQ Operation Mode Bypass Operation Mode No Operation (Sleep Mode) Min. Typ. 3 100 10 Max. 4 150 Unit mA uA uA
17
S5A1903X01
DATA PROCESSOR
PACKAGE DIMENSION
32 BCC TYPE
0.15 0.03 0.40 + 0.10 0.15 0.03 CAB C
CAB C
4.20
PIN CD.2
0.50 + 0.10 4.15
0.50 + 0.10
0.45 + 0.10
0.50 + 0.10
0.60 MAX B
5.00 + 0.10
0.75 + 0.025 INDEX ???? MARKING TYPES
4X A 0.15 / / 0.20 C
0.15
C
18
DATA PROCESSOR
S5A1903X01
9.00 + 0.30 7.00
+ 0.20
+ 0.30
9.00
7.00 #32
+ 0.20
#1 0.80 0.30
+ 0.10
(0.70)
0.10 MAX 170 MAX
+ 0.10
1.40
0.127 0.10 MAX 0.05 MIN
+ 0.10 - 0.05
0-8
0.50 + 0.20
19
S5A1903X01
DATA PROCESSOR
NOTES
20

▲Up To Search▲

Price & Availability of S5A1903X01-E0R0

	To Download S5A1903X01-E0R0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .